Home > Paint Finishes > Tikkurila / Valtti

Optiva 5 Matt - Durable Matt

Send to a friend Print

Description

Optiva Matt [5] - Durable matt

Description

Latex paint for walls and ceilings

Product features

Advanced scrub resistant matt for high traffic areas. High in solids Optiva 5 makes the applicators' life easy. With great application properties and high opacity Optiva 5 leaves a matt finish with deep colour.

Painting of gypsum boards, gypsum, cement-lime plasters, concrete substrates as well as for renovation of old coatings. Product may be used on wood and metal surfaces before application surface should be primed with suitable primer (Tikkurila Everal Primer, Tikkurila Everal Corrostop, Tikkurila Everal Metal Primer).

Recommended uses

Decorative painting of walls and ceilings inside residential, office and public use buildings and in schools and health care premises (hospitals, schools, kinder-gardens), workhouses and production plants and also food industry without direct contact with food.

zoom

TECHNICAL DATA

The paint is suitable for interior walls

The coverage of the paint on rough surfaces

16
m2/l

The coverage of the paint on smooth surfaces

16
m2/l

Base paints

A and C

Colour Range

Colours from colour cards Tikkurila Symphony, NCS, RAL.
Pallet of shades for over 10.000 colours.

Gloss grade

Matt

Coverage

Up to 16 m²/l max. with one coat. The coverage depends on absorbability, substrate texture, application method and colour.

Can sizes

Base A: 0.45 l (colour tester), 0.9 l, 2.7 l, 9 l, 18 l
Base C: 0.45 l (colour tester), 0.9 l, 2.7 l, 9 l

Thinner

Water

Application method

Brush, roller, spray (nozzle: 415/418, pressure: 150-180 bar).

Drying time at 23°C and 50% relative air humidity

At temperature +23°C, relative air humidity 50% the paint needs approx. 2 hours to dry. The interval between application of subsequent coats must be at least 4 hours. In lower temperatures and higher humidity the time between the application of next coat might be longer.

Wet scrub resistance

Highest – 1st class (according to norm: PN-EN 13300:2002). (PN-EN ISO 11998:2007P). In case of dirt on the surface for cleaning might be used water with delicate cleaning detergent.

Disinfectant resistance

Paint durable to cleaning with disinfectant agents used in hospitals. List of such products available on customer request.

Solids volume

Base A – approx. 52% wag., Base C – approx. 49% wag. (depend on colour).

Density

Base A – approx. 1.32 g/cm3, Base C – approx. 1.2 g/cm3 (depend on colour).

Storage

The product must be transported and stored in containers, which protect it against influence of atmospheric conditions. The storage and transport temperature must be between +5°C and +25°C. Protect the paint against frost. Close tightly the packaging immediately after use. Tightly closed packaging should be stored in room with temperature not lower than +5°C and not higher than +25°C, protect from frost and direct sunlight.

APPLICATION DETAILS

Application conditions

All surfaces to be painted must be dry, the temperature of the air at least +5°C, and the relative humidity of the air below 80%.

Preparation

Unpainted surfaces:
New plaster and concrete substrates can be painted after 4 weeks of seasoning. Clean these surfaces from dust and dirt, smooth out irregularities and losses with putty. Gypsum boards, cardboards and putty may be painted after they are fully dry. In case when unevenness of the surface is considerable, the wall should be even with leveling mortar and afterwards apply on the whole surface smooth putty. In case of small unevenness you may apply smooth putty at once. The use of above mentioned mortars and putty should be done according to data sheets of these products. Machine plaster with visible glossy sinter surface should be sanded and clean from dust. Then apply one coat of Tikkurila OPTIVA PRIMER, as finishing coat apply two coats of Tikkurila OPTIVA MATT [5] paint.

Previously painted surfaces:
Wash the surface before coating and remove grease and dirt and loose and flaking fragments of old coat. Sand glossy surfaces and smooth out irregularities and losses with putty. Paint with gloss grade: satin, semi-matt, semi-gloss and gloss should be sanded on the whole surface before final dusting. For sanding use sanding paper with grain 150 - 200. Prime the whole of substrate with Tikkurila OPTIVA PRIMER. Paint twice with the Tikkurila OPTIVA MATT [5] paint.

Surfaces painted with glue or lime paint: Remove thoroughly the lime or glue paint. Clean the surfaces from dust and dirt, smooth out irregularities and losses with putty. Then apply one coat of Tikkurila OPTIVA PRIMER, as finishing coat apply twice the Tikkurila OPTIVA MATT [5] paint. In case of loose substrate prime with impregnate Tikkurila SUPRABILIT.

Notice: It is recommended to check if the used putty is strong and stable surface – if after delicate hand wipe the putty is falling or leave the dust on hand then it means that the surface is loose and it has to be primed with Tikkurila Tikkurila SUPRABILIT impregnant.

Painting

Before application thin sufficient amount of paint from one production batch to avoid possible colour difference. Before painting stir the paint thoroughly. Depending on substrate porosity apply 2 coats of Tikkurila OPTIVA MATT [5] with brush, roller or spray. For colours of particularly weak hiding power (marked within the tinting system) it may be necessary to apply additional coats. In case of applying colours marked in tinting system as weakly hiding (LH) and intensive colours from C base, it is recommended to use priming paint Tikkurila OPTIVA PRIMER tinted to a colour close to the colour of finishing paint. The painting tape should be removed immediately after painting, before the paint will dry. It is recommended to use ANZA painting tools. Notice: Full resistance properties to wet cleaning, according to PN-EN 13300, coating achieves after 28 days from the end of painting.

Cleaning of tools

Before washing tools should be thoroughly wiped in order to remove as much paint. Clean tools with water immediately after the completion of the work.

EU VOC 2004/42/EC-limit value

Cat. A/a. The product contains a minimal amount of volatile organic compounds below 1,5 g/l (below the applicable standard). Since 2010 permissible VOC content is less than 30 g/l.